If you need assistance, please send an email to forum at 4hv dot org. To ensure your email is not marked as spam, please include the phrase "4hv help" in the subject line. You can also find assistance via IRC, at irc.shadowworld.net, room #hvcomm.
Support 4hv.org!
Donate:
4hv.org is hosted on a dedicated server. Unfortunately, this server costs and we rely on the help of site members to keep 4hv.org running. Please consider donating. We will place your name on the thanks list and you'll be helping to keep 4hv.org alive and free for everyone. Members whose names appear in red bold have donated recently. Green bold denotes those who have recently donated to keep the server carbon neutral.
Special Thanks To:
Aaron Holmes
Aaron Wheeler
Adam Horden
Alan Scrimgeour
Andre
Andrew Haynes
Anonymous000
asabase
Austin Weil
barney
Barry
Bert Hickman
Bill Kukowski
Blitzorn
Brandon Paradelas
Bruce Bowling
BubeeMike
Byong Park
Cesiumsponge
Chris F.
Chris Hooper
Corey Worthington
Derek Woodroffe
Dalus
Dan Strother
Daniel Davis
Daniel Uhrenholt
datasheetarchive
Dave Billington
Dave Marshall
David F.
Dennis Rogers
drelectrix
Dr. John Gudenas
Dr. Spark
E.TexasTesla
eastvoltresearch
Eirik Taylor
Erik Dyakov
Erlend^SE
Finn Hammer
Firebug24k
GalliumMan
Gary Peterson
George Slade
GhostNull
Gordon Mcknight
Graham Armitage
Grant
GreySoul
Henry H
IamSmooth
In memory of Leo Powning
Jacob Cash
James Howells
James Pawson
Jeff Greenfield
Jeff Thomas
Jesse Frost
Jim Mitchell
jlr134
Joe Mastroianni
John Forcina
John Oberg
John Willcutt
Jon Newcomb
klugesmith
Leslie Wright
Lutz Hoffman
Mads Barnkob
Martin King
Mats Karlsson
Matt Gibson
Matthew Guidry
mbd
Michael D'Angelo
Mikkel
mileswaldron
mister_rf
Neil Foster
Nick de Smith
Nick Soroka
nicklenorp
Nik
Norman Stanley
Patrick Coleman
Paul Brodie
Paul Jordan
Paul Montgomery
Ped
Peter Krogen
Peter Terren
PhilGood
Richard Feldman
Robert Bush
Royce Bailey
Scott Fusare
Scott Newman
smiffy
Stella
Steven Busic
Steve Conner
Steve Jones
Steve Ward
Sulaiman
Thomas Coyle
Thomas A. Wallace
Thomas W
Timo
Torch
Ulf Jonsson
vasil
Vaxian
vladi mazzilli
wastehl
Weston
William Kim
William N.
William Stehl
Wesley Venis
The aforementioned have contributed financially to the continuing triumph of 4hv.org. They are deserving of my most heartfelt thanks.
Registered Member #1530
Joined: Tue Jun 10 2008, 03:34PM
Location:
Posts: 32
So my DIY Variac box is all god and all, but the ammeter doesn't work well at all. It is a DC ammeter of course >.>
Anyway: My only challenge is that I don't want to use any active components (op amp, anything like that).
I think the meter has 75mV full scale movement. Can this be done? I could probably cobble up a transformer but I see a problem with rectification... Any suggestions?
Registered Member #1530
Joined: Tue Jun 10 2008, 03:34PM
Location:
Posts: 32
I tried to draw up a schematic to visualize it, but won't that give me DC out? My SSTC would be fine with that, but I have standard plugs on this box and would like to be able to use normal equipment with it.
I don't mind average vs peak vs RMS, just as it is now, it is either reading ~1 amp or >10 amps :0
Right now, there are 4 turns of wire around a toroid with the current-carrying wire passing through it and a large shottky... No resistor, and I doubt I will have a class that covers this material for another 2 years O.O
Should I be looking at the transformer as a current source?
--- EDIT
Guess it does work kind of like a current source. I did some (LT)Spice which gives me an idea where to head. It looks like:
I'd tweak R3 and R2 so that the scale works alright but am I on the right track?
Registered Member #2099
Joined: Wed Apr 29 2009, 12:22AM
Location: Los Altos, California
Posts: 1716
Let's say you want to use a current transformer, as opposed to the DC-ammeter-inside-bridge as suggested by Steve. The latter does deliver an AC sinusoidal voltage to the load, minus just two diode drops and the inconsequential voltage drop of ammeter shunt. Its main weakness is nonlinearity & distortion of voltage waveform at the extreme low end of Variac range.
Back to the current transformer. You need to allow secondary current Is = Ip / N to flow freely in both directions, and you need enough secondary voltage Vs = Ip * N to well exceed the drop of a rectifier diode, and you need to get rid of the current shunt in your meter.
Try this in Spice: a 100:1 current transformer with a 100 ohm resistor [called a burden] on the secondary. and no diode yet. Choose L1 = 1 uH, L2 = 10,000 uH, K = 0.99. With your sinusoidal current source of 10 peak amperes, we expect Is = 0.1 A peak (from turns ratio), so Vs = 10 V peak (Ohm's law) and Vp = 0.1 V peak (turns ratio again). The effective resistance on primary side is 0.01 ohm, which is Rs / N^2.
Now you can add a rectifed voltmeter in parallel with the burden resistor. Please let us know how that works out.
Registered Member #1232
Joined: Wed Jan 16 2008, 10:53PM
Location: Doon tha Toon!
Posts: 881
Yes, definitely put the CT burden after the bridge rectifier. Then the terminal voltage of the CT will rise to whatever is necessary to force the sense current to flow in the burden resistor. This compensates for the voltage drop of the diodes, which may vary with temperature, manufacturer, batch etc...
If you were to put the burden resistor directly across the CT output to convert it's current to a voltage, and then follow it with a bridge rectifier, there would be a gross measurement error, particularly for small currents. No DC output voltage would appear from the rectifier until there was enough current flowing to generate at least two "diode drops" worth of voltage across the burden. Only then would the rectifier start to conduct and produce some output. That is why it is not done this way!
Registered Member #2099
Joined: Wed Apr 29 2009, 12:22AM
Location: Los Altos, California
Posts: 1716
Yup, I figured out the [bridge] rectifier-in-series-with-burden last night. But Steve and Richie beat me to the punch, succinctly and articulately, so I'm not here editing yesterday's post. Got no firsthand experience with CT's feeding DC instruments, but have a DIY Variac box that has served for 30 years and could use an upgrade.
I hope my example L1 and L2 values help syntroniks to get his Spice simulations on track. Did some Googling to see if they were consistent with some real CT's. Found a surprisingly close match at http://www.surplussales.com/transformers/Pdfs/tm-pe-51687.pdf -- except those are made for 20 kHz and up.
A homebrew CT at 50 or 60 Hz must have a core big enough to avoid saturation. For about 2 volts peak on the secondary (based on bridge rectifer), the 100 turn example needs about 0.02 volts per turn, so a core area around 0.1 in^2 or 0.5 cm^2. I picked a suitable ferrite toroid in a catalog. It's almost big enough to wear on my pinky finger, and has a single-turn inductance of 3.6 uH.
Registered Member #30
Joined: Fri Feb 03 2006, 10:52AM
Location: Glasgow, Scotland
Posts: 6706
CTs for power frequency are made with toroidal laminated iron cores, and they're usually quite a bit bigger than pinky sized. I don't know if ferrite works well.
Registered Member #1232
Joined: Wed Jan 16 2008, 10:53PM
Location: Doon tha Toon!
Posts: 881
Mn/Zn ferrite doesn't work well for line frequency CTs at 50/60Hz) It's lack of distributed air-gap gives rise to rapid saturation as each cycle of current begins to flow. Once the ferrite is saturated, any further increase in output would be due to "rogowski coil" action I guess.
This site is powered by e107, which is released under the GNU GPL License. All work on this site, except where otherwise noted, is licensed under a Creative Commons Attribution-ShareAlike 2.5 License. By submitting any information to this site, you agree that anything submitted will be so licensed. Please read our Disclaimer and Policies page for information on your rights and responsibilities regarding this site.