If you need assistance, please send an email to forum at 4hv dot org. To ensure your email is not marked as spam, please include the phrase "4hv help" in the subject line. You can also find assistance via IRC, at irc.shadowworld.net, room #hvcomm.
Support 4hv.org!
Donate:
4hv.org is hosted on a dedicated server. Unfortunately, this server costs and we rely on the help of site members to keep 4hv.org running. Please consider donating. We will place your name on the thanks list and you'll be helping to keep 4hv.org alive and free for everyone. Members whose names appear in red bold have donated recently. Green bold denotes those who have recently donated to keep the server carbon neutral.
Special Thanks To:
Aaron Holmes
Aaron Wheeler
Adam Horden
Alan Scrimgeour
Andre
Andrew Haynes
Anonymous000
asabase
Austin Weil
barney
Barry
Bert Hickman
Bill Kukowski
Blitzorn
Brandon Paradelas
Bruce Bowling
BubeeMike
Byong Park
Cesiumsponge
Chris F.
Chris Hooper
Corey Worthington
Derek Woodroffe
Dalus
Dan Strother
Daniel Davis
Daniel Uhrenholt
datasheetarchive
Dave Billington
Dave Marshall
David F.
Dennis Rogers
drelectrix
Dr. John Gudenas
Dr. Spark
E.TexasTesla
eastvoltresearch
Eirik Taylor
Erik Dyakov
Erlend^SE
Finn Hammer
Firebug24k
GalliumMan
Gary Peterson
George Slade
GhostNull
Gordon Mcknight
Graham Armitage
Grant
GreySoul
Henry H
IamSmooth
In memory of Leo Powning
Jacob Cash
James Howells
James Pawson
Jeff Greenfield
Jeff Thomas
Jesse Frost
Jim Mitchell
jlr134
Joe Mastroianni
John Forcina
John Oberg
John Willcutt
Jon Newcomb
klugesmith
Leslie Wright
Lutz Hoffman
Mads Barnkob
Martin King
Mats Karlsson
Matt Gibson
Matthew Guidry
mbd
Michael D'Angelo
Mikkel
mileswaldron
mister_rf
Neil Foster
Nick de Smith
Nick Soroka
nicklenorp
Nik
Norman Stanley
Patrick Coleman
Paul Brodie
Paul Jordan
Paul Montgomery
Ped
Peter Krogen
Peter Terren
PhilGood
Richard Feldman
Robert Bush
Royce Bailey
Scott Fusare
Scott Newman
smiffy
Stella
Steven Busic
Steve Conner
Steve Jones
Steve Ward
Sulaiman
Thomas Coyle
Thomas A. Wallace
Thomas W
Timo
Torch
Ulf Jonsson
vasil
Vaxian
vladi mazzilli
wastehl
Weston
William Kim
William N.
William Stehl
Wesley Venis
The aforementioned have contributed financially to the continuing triumph of 4hv.org. They are deserving of my most heartfelt thanks.
Registered Member #2939
Joined: Fri Jun 25 2010, 04:25AM
Location:
Posts: 615
For lowest EMI keep the switched node as small as possible. In the application example you posted that would be the junction of M1,M2 and L1. Also planes are not a panacea for all ills - remember "current flows in loops" so you should always consider the return path of every signal. Sometimes you might want to steer a noisy or large current away from something sensitive, like your current sense amplifier. This can be done by adding slits to the plane in appropriate places.
Registered Member #2939
Joined: Fri Jun 25 2010, 04:25AM
Location:
Posts: 615
It would help if you post an annotated schematic /pcb so we can see what is where. The thing to watch out for is the ground plane isn't the same voltage everywhere if there are large currents flowing. So if your feedback needs to be referenced to the 0V leg of the controller chip then your sense amps need to be referenced to that point too, which means you dont want large currents flowing in the copper between the two - you might be better to run a separated ground from the controller to the sense amps.
Running a gnd trace around a sensitive area may be helpful in some cases, but it depends on the nature of the interference you are trying to stop.
Registered Member #3637
Joined: Fri Jan 21 2011, 11:07PM
Location: Buffalo, NY
Posts: 1068
Here!
I made a schematic and tried annotating the PCB layout a little bit. Link is to a gallery with both shown.
All of the part numbers shown on the schematic image line up with the ones on the PCB; i.e. R5 is R5, C1 is C1, etc.
I know I'm not the best at making schematics so I apologize, but I hope it's readable and understandable.
One other big question, is am I suppose to have my "bulk" capacitance before or after the sense resistor? Or should I realistically have bulk capacitance before AND after?
Additionally, some of the values of components aren't shown; they're likely going to be figured out experimentally.
Registered Member #2939
Joined: Fri Jun 25 2010, 04:25AM
Location:
Posts: 615
I would put your bulk C before the Isense, otherwise you will be measuring the ripple current from the inductor as well. Your CV/CC implementation wont work - you have both V and I feedback running to a summing junction - which is not what you want. You need the greater of V or I to control the regulator, not the sum. You need to join the two via precision rectifiers.
I would also allow for a gate resistor on each mosfet - you may not need them, but if you do then having the footprint on the pcb will make life much easier.
You really ought to try simulating the circuit before you build anything. At least do the CC/CV bit.
Registered Member #3637
Joined: Fri Jan 21 2011, 11:07PM
Location: Buffalo, NY
Posts: 1068
Does it need to be a precision rectifier, or would just using two low Vdrop diodes by themselves work?
And I actually do have spaces for gate resistors on two of the fets already, so that's taken care of. I'll add one for the last one too.
And I'll also move the bulk capacitance before the sense resistor.
and I did actually try to do a simulation on LTspice with it, but the output didn't make sense and the entire thing ran INCREDIBLY slowly. It feels very archaic for some reason.
Oh, and should I have the feedback for CV be after or for the sense resistor too? Or does that not overly matter?
Registered Member #3637
Joined: Fri Jan 21 2011, 11:07PM
Location: Buffalo, NY
Posts: 1068
Updated the PCB. Moved the current sense amp down, farther away from the switching node. Made special care to try to avoid any power ground/signal ground loops with it too.
Added two rectifiers from the CV and CC feedback nodes to the main feedback loop. They're D5 and D7.
Also moved the bulk output cap to a new spot, and added another one for more filtering, and added another plane so the two sides of the PCB conduct current for it.
Added more vias and fixed some layout issues regarding the ground planes; they're more continuous and don't pinch down in any specific spot.
Registered Member #2939
Joined: Fri Jun 25 2010, 04:25AM
Location:
Posts: 615
The reason I suggest using a precision rectifier is the temp coefficient of ordinary diodes will screw up your output voltage / current as they heat or cool. A dual opamp for this job is pretty cheap ( it doesn't need to be anything fancy - just unity gain stable) and makes the problem just go away. I would put Vsense right on the output terminals of your supply, because thats the voltage you are trying to control.
I did a quick and dirty on the power section to show you a more compact way to lay out the heart of the converter. This minimises all the current path lengths, and noisy node areas, and puts all the semis on one side for a single heatsink as suggested by Hen918. The yellow is where the top and bottom layers overlap - its a bit ugly, but you'll get the idea. I haven't tried to route out the gate signals - I wouldn't want to spoil your fun. I know the sizes of the parts will be wrong but its just conceptual.
Registered Member #3637
Joined: Fri Jan 21 2011, 11:07PM
Location: Buffalo, NY
Posts: 1068
Ah okay!
That makes sense.
I squeezed in a basic dual op amp right next to the LTC1775;
Uses an LM2904, really cheap and "internally compensated with unity gain" ? I assume that means it's unity gain stable.
Edit: Just gonna use an LM358 instead. They're a fraction cheaper and from what I read they're unconditionally unity gain stable.
Also uses a really cheap dual common cathode signal diode, so all in all adds a whole 47 cents to the cost. Not bad. If it adds more stability then great.
And I do understand the mounting on one heatsink thing, however I'm kind of smitten with the layout I have... I hope it doesn't cause any issues but we'll see. Plus I actually like being able to use individual heatsinks. I have small ones that work perfectly.
The layout I have is actually pretty similar to the chinese version I'm loosely basing this off of.
Registered Member #2939
Joined: Fri Jun 25 2010, 04:25AM
Location:
Posts: 615
If you like your layout, then go for it. Engineering is as much art as science. I'm used to being constrained by things such as budgets or EMC standards, so I tend to optimize for those things automatically - that's what 30 years in the game does to you!
This site is powered by e107, which is released under the GNU GPL License. All work on this site, except where otherwise noted, is licensed under a Creative Commons Attribution-ShareAlike 2.5 License. By submitting any information to this site, you agree that anything submitted will be so licensed. Please read our Disclaimer and Policies page for information on your rights and responsibilities regarding this site.