If you need assistance, please send an email to forum at 4hv dot org. To ensure your email is not marked as spam, please include the phrase "4hv help" in the subject line. You can also find assistance via IRC, at irc.shadowworld.net, room #hvcomm.
Support 4hv.org!
Donate:
4hv.org is hosted on a dedicated server. Unfortunately, this server costs and we rely on the help of site members to keep 4hv.org running. Please consider donating. We will place your name on the thanks list and you'll be helping to keep 4hv.org alive and free for everyone. Members whose names appear in red bold have donated recently. Green bold denotes those who have recently donated to keep the server carbon neutral.
Special Thanks To:
Aaron Holmes
Aaron Wheeler
Adam Horden
Alan Scrimgeour
Andre
Andrew Haynes
Anonymous000
asabase
Austin Weil
barney
Barry
Bert Hickman
Bill Kukowski
Blitzorn
Brandon Paradelas
Bruce Bowling
BubeeMike
Byong Park
Cesiumsponge
Chris F.
Chris Hooper
Corey Worthington
Derek Woodroffe
Dalus
Dan Strother
Daniel Davis
Daniel Uhrenholt
datasheetarchive
Dave Billington
Dave Marshall
David F.
Dennis Rogers
drelectrix
Dr. John Gudenas
Dr. Spark
E.TexasTesla
eastvoltresearch
Eirik Taylor
Erik Dyakov
Erlend^SE
Finn Hammer
Firebug24k
GalliumMan
Gary Peterson
George Slade
GhostNull
Gordon Mcknight
Graham Armitage
Grant
GreySoul
Henry H
IamSmooth
In memory of Leo Powning
Jacob Cash
James Howells
James Pawson
Jeff Greenfield
Jeff Thomas
Jesse Frost
Jim Mitchell
jlr134
Joe Mastroianni
John Forcina
John Oberg
John Willcutt
Jon Newcomb
klugesmith
Leslie Wright
Lutz Hoffman
Mads Barnkob
Martin King
Mats Karlsson
Matt Gibson
Matthew Guidry
mbd
Michael D'Angelo
Mikkel
mileswaldron
mister_rf
Neil Foster
Nick de Smith
Nick Soroka
nicklenorp
Nik
Norman Stanley
Patrick Coleman
Paul Brodie
Paul Jordan
Paul Montgomery
Ped
Peter Krogen
Peter Terren
PhilGood
Richard Feldman
Robert Bush
Royce Bailey
Scott Fusare
Scott Newman
smiffy
Stella
Steven Busic
Steve Conner
Steve Jones
Steve Ward
Sulaiman
Thomas Coyle
Thomas A. Wallace
Thomas W
Timo
Torch
Ulf Jonsson
vasil
Vaxian
vladi mazzilli
wastehl
Weston
William Kim
William N.
William Stehl
Wesley Venis
The aforementioned have contributed financially to the continuing triumph of 4hv.org. They are deserving of my most heartfelt thanks.
Could have PFC stage boost to 565VDC instead, and then full bridge -> 400VAC sine wave. Don't think it's worth it, as the reduction in core losses will probably be less than the increase in switching losses.
Where did you get the spreadsheet you are using for the calculations?
I'm trying to repeat the minimum turns to stay out of saturation and I'm getting lower numbers. 73 turns producing 1.1T rather than 1.6 at 50Hz. I think the 400Hz route is weird and I'm wondering if keeping the cores split would let you put enough copper on to get decent performance at 50Hz.
Btw what fraction of your winding window are you planning to use?
I also have a probably insane idea to track the 50Hz waveform and switch polarity at the peak to get you pseudo 100Hz. It's ugly, but wouldn't need big capacitors.
That makes two of us :) My formal education in this area goes as far as a lecturer skimming over something along the lines of "Voltage ratio = turns ratio, don't have too few turns or it won't work".
Wastrel wrote ...
Where did you get the spreadsheet you are using for the calculations?
I made it, so it's both poorly laid out and probably incorrect.
Wastrel wrote ...
I'm trying to repeat the minimum turns to stay out of saturation and I'm getting lower numbers. 73 turns producing 1.1T rather than 1.6 at 50Hz.
(possibly dodgy calculations follow)
Erms = 4.44 * f * N * a * Bpeak.
Setting Bpeak = 1.1T, f = 50Hz, Erms = 400V and a = 0.01729m^2 after applying 95% stacking factor, solving gives N = 95 turns.
For a square wave, 4.44 is changed to 4 and N = 105.
Can you post your calculations to compare with?
Wastrel wrote ...
I think the 400Hz route is weird and I'm wondering if keeping the cores split would let you put enough copper on to get decent performance at 50Hz.
I've copied the spreadsheet and adjusted it for a single small (H = 70mm) core to 5500V and 7.5kVA capacity. Paralleling the primaries and putting the secondaries in series would then allow for equivalent capacity. Looks like overall losses will end up being higher.
As the number of layers goes up, the calculation for number of layers becomes inaccurate due to not properly accounting for the reduction in inner diameter. I'll have a go at fixing that later.
Wastrel wrote ...
Btw what fraction of your winding window are you planning to use?
Hoping to use as few layers as reasonably possible to improve heat dissipation and make it easier to wind - a 26mmx14mm cross-section bicycle wheel needs to fit through it for winding.
Wastrel wrote ...
I also have a probably insane idea to track the 50Hz waveform and switch polarity at the peak to get you pseudo 100Hz. It's ugly, but wouldn't need big capacitors.
Chopping the input waveform like that is an interesting idea, I don't know whether it will work. Hopefully someone else can chime in on that.
Wastrel wrote ...
What is the transformer for?
Aim: To wind a transformer with similar capacity and losses as a small pole pig, except smaller/cheaper due to operating at a higher frequency.
I could have sworn the voltage on the spreadsheet was 325Vish, has it been changed? That's the main reason my numbers are wrong.
I have the feeling that the capacitor this is going to need will be huge, and the current requirement will make it expensive.
The energy wasted is quite flat and I think it's to do with how you are calculating copper used. Fixed diameter wire, single winding. I think if you wind more copper on the core the power wasted will drop. Tape for the primary for example. This may make it optimal to use a lower frequency than 400hz and radiate much less total heat.
You know about interleaving primary and secondary windings, right? This will be harder given the secondary voltage.
I'm surprised splitting the cores isn't better, but then the main advantage would be to use more copper. I'd also consider hacksawing away some of the inner ring, which would cost you some area but open up the winding window a lot.
How did you calculate the cross sectional area of core you needed for 15kva? I know you are in the right ball park for 50Hz operation but I'm quite fuzzy on the actual maths for that. You may have much more metal than you need for 400Hz (are proportionally more hysteresis loss).
My transformer theory is weak as I said, I have done a lot of reading for a core of my own and I know enough to know I don't know what I'm talking about. Some things I think are generally true are that toroidal cores are good for low leakage of flux and can have a huge winding window compared to E cores, but that you pay a heavy price if you don't fill most of it with copper.
Something else I think is true is that for a resistive load your copper losses should be highest when the load draws full current, and the core losses should be highest when the load draws no current. This make sense to you?
Registered Member #11591
Joined: Wed Mar 20 2013, 08:20PM
Location: UK
Posts: 556
Using your formula, and rearranging to find N, I got Erms/(f*a*Bpeak*4.44). using 4 instead of 4.44, f=400, a=0.01729, Bpeak=1.1 and Erms=400, I got 1/(4*0.01729*1.1)= 13.14475turns.
Registered Member #3343
Joined: Thu Oct 21 2010, 04:06PM
Location: Toronto
Posts: 311
Ross First let us know: Service factor: 1 for continuous service at full load, 0,5 for work 5 minutes in a period of 10 minutes, 0.2 for working 2 minutes in a period of 10 minutes. (Welding machines transformers are designed for .2~.5 service factor) Second : Do you have intention of add a small fan to cool the core ? Third: Use all units as IS system. m for meter, kg for weight, T for tesla, V for volt A for amper Etc Do not play with gauss, oersted, gilberts, centimeter, inch, pound, once, inch etc etc Third: Define yours design parameters
This site is powered by e107, which is released under the GNU GPL License. All work on this site, except where otherwise noted, is licensed under a Creative Commons Attribution-ShareAlike 2.5 License. By submitting any information to this site, you agree that anything submitted will be so licensed. Please read our Disclaimer and Policies page for information on your rights and responsibilities regarding this site.