If you need assistance, please send an email to forum at 4hv dot org. To ensure your email is not marked as spam, please include the phrase "4hv help" in the subject line. You can also find assistance via IRC, at irc.shadowworld.net, room #hvcomm.
Support 4hv.org!
Donate:
4hv.org is hosted on a dedicated server. Unfortunately, this server costs and we rely on the help of site members to keep 4hv.org running. Please consider donating. We will place your name on the thanks list and you'll be helping to keep 4hv.org alive and free for everyone. Members whose names appear in red bold have donated recently. Green bold denotes those who have recently donated to keep the server carbon neutral.
Special Thanks To:
Aaron Holmes
Aaron Wheeler
Adam Horden
Alan Scrimgeour
Andre
Andrew Haynes
Anonymous000
asabase
Austin Weil
barney
Barry
Bert Hickman
Bill Kukowski
Blitzorn
Brandon Paradelas
Bruce Bowling
BubeeMike
Byong Park
Cesiumsponge
Chris F.
Chris Hooper
Corey Worthington
Derek Woodroffe
Dalus
Dan Strother
Daniel Davis
Daniel Uhrenholt
datasheetarchive
Dave Billington
Dave Marshall
David F.
Dennis Rogers
drelectrix
Dr. John Gudenas
Dr. Spark
E.TexasTesla
eastvoltresearch
Eirik Taylor
Erik Dyakov
Erlend^SE
Finn Hammer
Firebug24k
GalliumMan
Gary Peterson
George Slade
GhostNull
Gordon Mcknight
Graham Armitage
Grant
GreySoul
Henry H
IamSmooth
In memory of Leo Powning
Jacob Cash
James Howells
James Pawson
Jeff Greenfield
Jeff Thomas
Jesse Frost
Jim Mitchell
jlr134
Joe Mastroianni
John Forcina
John Oberg
John Willcutt
Jon Newcomb
klugesmith
Leslie Wright
Lutz Hoffman
Mads Barnkob
Martin King
Mats Karlsson
Matt Gibson
Matthew Guidry
mbd
Michael D'Angelo
Mikkel
mileswaldron
mister_rf
Neil Foster
Nick de Smith
Nick Soroka
nicklenorp
Nik
Norman Stanley
Patrick Coleman
Paul Brodie
Paul Jordan
Paul Montgomery
Ped
Peter Krogen
Peter Terren
PhilGood
Richard Feldman
Robert Bush
Royce Bailey
Scott Fusare
Scott Newman
smiffy
Stella
Steven Busic
Steve Conner
Steve Jones
Steve Ward
Sulaiman
Thomas Coyle
Thomas A. Wallace
Thomas W
Timo
Torch
Ulf Jonsson
vasil
Vaxian
vladi mazzilli
wastehl
Weston
William Kim
William N.
William Stehl
Wesley Venis
The aforementioned have contributed financially to the continuing triumph of 4hv.org. They are deserving of my most heartfelt thanks.
Registered Member #1062
Joined: Tue Oct 16 2007, 02:01AM
Location:
Posts: 1529
max gate current is 3amp, resistance of the gate is 15ohm according to my mulltimeter, but the supply still shorts, so its wrong. since its shorting, it means its giving 4.5amps short pulse into gate.
Registered Member #511
Joined: Sat Feb 10 2007, 11:36AM
Location: Somerset UK
Posts: 55
Hi rp181
It`s nice to see someone building a multistage coilgun, they can be much more efficient than single stage.
I hope you will forgive me but I do not understand your schematic. I do not think it will work as a trigger because you have the SCR connected between the output and discharge pins. If you want a detailed discusion on triggering it may be wise to take it to the accelerators board.
Registered Member #1062
Joined: Tue Oct 16 2007, 02:01AM
Location:
Posts: 1529
I just tooke the schematic from the website posted in original post. When the beam is broken, the 555 sends the signal through output, and discharge acts as ground (0v)?
Registered Member #511
Joined: Sat Feb 10 2007, 11:36AM
Location: Somerset UK
Posts: 55
Hi rp181
There is a transistor between the discharge pin and ground, when the output is high the discharge transistor is off and when the output is low the discharge transistor is on. The output of the 555 is only rated for 200mA, in an earlier post you were talking about currents of several Amps. I would suggest you use an amplifier stage after the 555 to get more current.
When the beam is broken the reset pin is taken high but the 555 will not trigger because the trigger pin is held high by C4 (the trigger is active low). This site has good information on NE555 circuits Electronics Club or you could try searching for datasheets and application notes for the NE555.
Registered Member #1062
Joined: Tue Oct 16 2007, 02:01AM
Location:
Posts: 1529
Good point ozzy, i forgot that to open fully/fastest it needs ~3A. do you think a MJE3055T (from fairchild) will work?
UPDATE: I wired all the resistors in parrallel, giving combined resistance of 200ohms. So at 400v, it will draw ~400W, well below the 1500W rating of the bank, And WELL below the rating of 15KW for 10sec.
I was looking at fairchild's infrared diodes, and im confused by all the options/ properties. Which properties should i look for in a detector beam?
This site is powered by e107, which is released under the GNU GPL License. All work on this site, except where otherwise noted, is licensed under a Creative Commons Attribution-ShareAlike 2.5 License. By submitting any information to this site, you agree that anything submitted will be so licensed. Please read our Disclaimer and Policies page for information on your rights and responsibilities regarding this site.