If you need assistance, please send an email to forum at 4hv dot org. To ensure your email is not marked as spam, please include the phrase "4hv help" in the subject line. You can also find assistance via IRC, at irc.shadowworld.net, room #hvcomm.
Support 4hv.org!
Donate:
4hv.org is hosted on a dedicated server. Unfortunately, this server costs and we rely on the help of site members to keep 4hv.org running. Please consider donating. We will place your name on the thanks list and you'll be helping to keep 4hv.org alive and free for everyone. Members whose names appear in red bold have donated recently. Green bold denotes those who have recently donated to keep the server carbon neutral.
Special Thanks To:
Aaron Holmes
Aaron Wheeler
Adam Horden
Alan Scrimgeour
Andre
Andrew Haynes
Anonymous000
asabase
Austin Weil
barney
Barry
Bert Hickman
Bill Kukowski
Blitzorn
Brandon Paradelas
Bruce Bowling
BubeeMike
Byong Park
Cesiumsponge
Chris F.
Chris Hooper
Corey Worthington
Derek Woodroffe
Dalus
Dan Strother
Daniel Davis
Daniel Uhrenholt
datasheetarchive
Dave Billington
Dave Marshall
David F.
Dennis Rogers
drelectrix
Dr. John Gudenas
Dr. Spark
E.TexasTesla
eastvoltresearch
Eirik Taylor
Erik Dyakov
Erlend^SE
Finn Hammer
Firebug24k
GalliumMan
Gary Peterson
George Slade
GhostNull
Gordon Mcknight
Graham Armitage
Grant
GreySoul
Henry H
IamSmooth
In memory of Leo Powning
Jacob Cash
James Howells
James Pawson
Jeff Greenfield
Jeff Thomas
Jesse Frost
Jim Mitchell
jlr134
Joe Mastroianni
John Forcina
John Oberg
John Willcutt
Jon Newcomb
klugesmith
Leslie Wright
Lutz Hoffman
Mads Barnkob
Martin King
Mats Karlsson
Matt Gibson
Matthew Guidry
mbd
Michael D'Angelo
Mikkel
mileswaldron
mister_rf
Neil Foster
Nick de Smith
Nick Soroka
nicklenorp
Nik
Norman Stanley
Patrick Coleman
Paul Brodie
Paul Jordan
Paul Montgomery
Ped
Peter Krogen
Peter Terren
PhilGood
Richard Feldman
Robert Bush
Royce Bailey
Scott Fusare
Scott Newman
smiffy
Stella
Steven Busic
Steve Conner
Steve Jones
Steve Ward
Sulaiman
Thomas Coyle
Thomas A. Wallace
Thomas W
Timo
Torch
Ulf Jonsson
vasil
Vaxian
vladi mazzilli
wastehl
Weston
William Kim
William N.
William Stehl
Wesley Venis
The aforementioned have contributed financially to the continuing triumph of 4hv.org. They are deserving of my most heartfelt thanks.
Registered Member #61905
Joined: Sun Nov 12 2017, 03:27AM
Location:
Posts: 23
I've seen a few pictures of people winding their own toroids for GDT but is anyone winding their own power inductors? Anyone have tips? I've done a few in single layer to keep the parasitic capacitance low, but I'm looking for ways to improve the results. For buck/boost converters it seems like multiple parallel conductors would help some with skin effect, but should they be braided or twisted?
I'm sure there are limitations of what can be done with the machine wound toroids, but as a hobbyist are there techniques that can improve the results?
Registered Member #2431
Joined: Tue Oct 13 2009, 09:47PM
Location: Chico, CA. USA
Posts: 5639
I wind special inductive circuits ALL the TIME ! and you should too! Its really hard to get power or frequency or saturation that you want, whether it be power or signal. And buying pre-made inductors and transformers is the most expensive way to get them.
The only issue ive found with making your own is the length of each unique strand. Assuming your core was made as one piece or is glued and now inseparable.
Calculate your skin effect there are calculators on google for that. but honestly smaller strands in parallel will cool better, bend better and make better packing efficiency through the window. above 150 kHz i think is where skin effect begins to be a problem in power inductors.
Not sure how far you want to go or how much advice you want but i have more info and examples if you like.
I will give you one piece of advice above all else: buy solder-able magnet wire. If not you'll regret it.
Let me show you some of my arsenal :
liberated black ferrite, added all thread to each end to mount.
Registered Member #61905
Joined: Sun Nov 12 2017, 03:27AM
Location:
Posts: 23
Thanks for the great reply! Is that first picture the circuit that you use to test your inductors/transformers?
This is a picture of a factory wound toroid and a hand wound version that I made:
It uses 3 parallel strands, which are easier to bend, as you mentioned. I used a drop of super glue to secure the ends against the core. The 3-strand windings also have the advantage of being able to "bunch up" on the inside diameter and spread out on the outside diameter. I don't know how well the 3 strands share the electrical load, but the hand wound replacement runs cooler than the original part.
Patrick wrote ... The only issue ive found with making your own is the length of each unique strand. Assuming your core was made as one piece or is glued and now inseparable.
Happily, the length I calculated was pretty close to what was needed. I left the strands a bit long to be safe, but I didn't end up wasting much wire. The inner 3rd strand is only a couple inches longer than the two beneath it.
Registered Member #230
Joined: Tue Feb 21 2006, 08:01PM
Location: Gracefield lower Hutt
Posts: 284
I remove used ferrite transformers from the pcb and submerge the pin out pins in a brine solution in a soup bowl and microwave the transformer for about a minute. Careful as the core absorbs the microwave radiation like a sponge and gets extremely hot you can then pull the core halves out as the heat softens the potting varnish
Registered Member #2431
Joined: Tue Oct 13 2009, 09:47PM
Location: Chico, CA. USA
Posts: 5639
your already off to good winding skills. Next study powdered metal, ferrite, iron tape/lamination and geometry.
johnf wrote ...
I remove used ferrite transformers from the pcb and submerge the pin out pins in a brine solution in a soup bowl and microwave the transformer for about a minute. Careful as the core absorbs the microwave radiation like a sponge and gets extremely hot you can then pull the core halves out as the heat softens the potting varnish
wow, never heard this ! looks like i learned from this thread too !
flyrod wrote ...
Is that first picture the circuit that you use to test your inductors/transformers?
No thats a full featured custom SMPS, meant to put out 500 or more watts from a wall socket. its just for signal testing the ICs at the moment it does use that 250 watt atx core.
its the first module of a future power factor corrected 240 VAC 2kW smps which will be isolated and put out 20-30kV in a single step. hopefully with a fixed load it can stay near 95% eff. that means 100 watts of heat, still alot.
but thats a lot of ifs' and maybes' its already been 2 years.
Registered Member #3414
Joined: Sun Nov 14 2010, 05:05PM
Location: UK
Posts: 4245
I just finished winding the one on bottom right of picture last night.
I'm using 3" type 26 D toroids (the D stands for double thickness)
wire on both is 14 SWG, if I recall correctly, 1.8mm diameter, 2.5mm^2 cross section, good for 9.6 Amps, apparently (10 amp)
the one on lower left is, if I recall correctly, 1.75mH, and has 250 grammes of wire
The one on the right has 500 grammes of wire. This worked out to be exactly four layers.
Winding it was a nightmare, the first layer was very slow going, with lots of bird's nests to untangle. Part way through the second layer it became a bit more manageable. By the third layer the wire had started to work harden, this just bacame worse and worse, but at least the length of wire was more manageable.
I started winding it weeks ago, then had a break while I was doing other things, then finished it off over the past week.
I've another half a dozen or so to wind, but not in a rush to start the next one yet.
It's not as pretty as it might be, my brain had turned to jelly by the time it was finished.
They will be used for conditioning the power supply for a single ended class A amp, along with about forty 4700uF stud mount electrolytics
EDIT: I've not yet measured the second one, I'm aiming for around four mH but will be happy with whatever I get, I only need around 2-2.5 mH, anything else is a bonus. I'll post details of the test over on my thread regarding powe supply simulators.
Registered Member #61905
Joined: Sun Nov 12 2017, 03:27AM
Location:
Posts: 23
So in this picture of a power supply, there are a variety of toroids:
In some cases the parallel strands are twisted together before being wound on the core. Why would you do this vs. parallel strands not twisted together?
Registered Member #230
Joined: Tue Feb 21 2006, 08:01PM
Location: Gracefield lower Hutt
Posts: 284
It maximises surface area for skin effect and twisting together as they in parallel reduces the interwinding capacitance so raises the self resonant frequency
This site is powered by e107, which is released under the GNU GPL License. All work on this site, except where otherwise noted, is licensed under a Creative Commons Attribution-ShareAlike 2.5 License. By submitting any information to this site, you agree that anything submitted will be so licensed. Please read our Disclaimer and Policies page for information on your rights and responsibilities regarding this site.